header logo

Go Back   Checkmate Community Boating Forums > Blogs > Old Hickory's 1983 Checkmate Enforcer Restoration
Portal Home Register Blogs FAQ Calendar Mark Forums Read

Main Menu
Module Jump:
Google Search
Google
Latest Poll
January 2020's Boat of the Month Vote!
This poll is closed
I vote for "PA-Checkmate's" Convincor! 0 0%
I vote for "KevinR's" Pulsare! 0 0%
I vote for "PA-Checkmate's" Convincor! 1 11%
I vote for "CheckmateFever's" Group Shot! 1 11%
I vote for "TuGHiLLBoYs" Convincor Shot! 0 0%
I vote for "Burton95p's" ZT230! 7 78%
Voters: 9 100%
Notices

Welcome to the Checkmate Community Forums

This is a tale of my journey to aquiring and restoring a true classic; the Checkmate Enforcer. I hope it will be entertaining as well as informative.

Most all that I will do and describe will probably be thrown to the wind in the forums first; so I know each of will have a part in the telling of this story. Thanks in advance for all that each of you have done so far, and for what you will do in the future.
Rating: 2 votes, 5.00 average.

Part 8: Building the transom

Posted 06-04-2008 at 01:34 AM by Old Hickory
Updated 06-05-2008 at 03:06 AM by Old Hickory

Finally getting around to building the first structural parts to my Enforcer. Once the transom was out it was on to making a pattern from the old one; cutting and glueing it all up.

First decision I had to make was to determine what materials I was going to use. I initially was going to build the transom out of Douglas fir due to it's strength and cost effectiveness; but was eventually swayed by several members, one in particular, to give Coosa board a try. The one draw back was cost.

Coosa board is manufactured by Coosa Composites LLC, in Pelham, AL. It is a high density polyurethane foam, reinforced with layers of woven roving and continuous strand fiberglass. Their Bluewater series panels come in 2 different densities. B-26 has their highest strength to weight ratio with a density of 26lbs/sqft and is 30% lighter than plywood.
B-20 has a density of 20lbs/sqft and is 45% lighter than plywood. This from Coosa's website.

As I mentioned earlier, it is expensive. Cost comparison to plywood is as follows:

B-26 3/4" 4'x8' panel $195
B-26 1/2" 4'x8' panel $183
B-20 1/2" 4'x8' panel $129
(Advanced Plastics; Nashville, Tn.)

DFir 3/4" 4'x8' panel $71
DFir 1/2" 4'x8' panel $58
(Nashville Plywood Inc.)

Once I got over the initial sticker shock and found some additional structural products that were actually cheaper than ply,(I'll cover that in a later thread when I get to stringer and floor replacement), the over all cost would not be too much different than ply.

So now I have purchased the Coosa and I am ready to begin the process of making a pattern from my old transom. Here are the tools I used for this part of the rebuild.



First I ground the bondo off the old transom so that tracing would be more accurate.





I made the pattern by tracing the old transom onto a large piece of cardboard from a refrigerator box and then cutting it out with a utility knife.



Doyle watching me cut the pattern



Couple of pics of the finished pattern





You may have noticed that I do not have the engine cut out for the splashwell. I have eliminated it and will be building the transom ala convincor style.

Next I began tracing the pattern on the coosa using clamps and a sharpie. You may notice in several of the pics of the pattern I marked "R" and "L". The original wood transom wasn't completly uniform from right to left. So I marked the pattern and my coosa panels to be sure the glued panels would be consistent.





I was able to get two pieces of my transom off of one B-26 panel; however there was a small area of overlap.



You'll see how I address this later.

Now to cutting; this stuff cuts like butter! I fired up my jigsaw, took a deep breath, and began...



Now many of you know that when you're doing the hot nasty stuff, the kids are nowhere to be found. But as soon as the power tools are out they are all eager to help.

Here's a few pics of two of my boys helping me "cut the coosa"





First panel cut, with the help of my youngest



All three cut and ready for glueing



Here is a pic of the panel that was the victim of the overlap. I cut a small piece to fit the gap.



This panel and the fitted piece will be sandwiched between the other B-26 panel and a panel of B-20. If you havn't figured it out yet that will give me 2" for the structural core of the new transom as opposed to the 1 1/4" from the factory ply panel.

Now it's time for the glueing. I chose to use PL Premium Construction adhesive due to it's lower cost as compared to 3M 5200 Fast Cure. I had found it was being used, by wooden boat builders on another forum, with excellent results.

3M 5200 was $11.45/10oz tube
PL Premium was $3.39/10oz tube.

They are both polyurethane adhesives with virtually identical specifications(see the attachments at the end of the post).

Advanced plastics only had 7 tubes of 3M and I would have to order by the case for any more. Lowes has PL on the shelf and I can buy it buy the tube or case; 1/4 the cost to boot.

I started by wiping down all the panels of coosa with a surgical towel to ensure a clean dry surface.

I decided that troweling the adhesive would be the most efficient means of getting it uniform. I used a standard notched trowel I purchased from Lowes.



I applied the PL with a caulk gun and began troweling







It took three 10 oz tubes to cover the surface of the panel. I took the second B-26 panel and laid it on top; then glued the fitted piece in.



And then applied the second round of PL and troweled. I used a total of six 10oz tubes for the the two sides.



I laid the panel of B-20 on the troweled surface; made sure all the edges were aligned; then placed 200 lbs of weight on top to let it cure over night. I added another 50 lbs after I took this photo.



I was very impressed as to how well this stuff troweled. A notched trowel is the only way to go in my opinion. Clean up was a snap using a rag soaked in acetone.

Tomorrow I will remove the weight and will begin shaping the edges and getting the transom prepped for bedding and glassing in this weekend.

Thanks again for looking!

Hick





I have to give alot of thanks to several members here:175checkmate; teamhart2; jallen355; compulse170; LAallison; wca_tim. thanks guys for all your input
Attached Thumbnails
Click image for larger version

Name:	PL Premium Tech Data.jpg
Views:	3822
Size:	121.3 KB
ID:	2   Click image for larger version

Name:	TECHNIAL BULLETIN PL 1.jpg
Views:	3334
Size:	118.6 KB
ID:	3   Click image for larger version

Name:	Mediawebserver.jpg
Views:	3307
Size:	103.2 KB
ID:	4  
Posted in Uncategorized
Views 32892 Comments 7
Total Comments 7

Comments

  1. Old Comment
    Old Hickory's Avatar
    here's the second page to the 3M specs; blog wouldn't let me add a fourth attachment.

    Posted 06-04-2008 at 06:27 PM by Old Hickory Old Hickory is offline
  2. Old Comment
    Rob B's Avatar
    Hick it's looking good, I'm glad I could be of some help. I kinda wish I was close by to help/watch. I love to build/fix stuff. The kids look like they're having fun with Dad. Btw, Doyle looks good.
    Posted 06-04-2008 at 10:35 PM by Rob B Rob B is offline
  3. Old Comment
    Old Hickory's Avatar
    thanks for the moral support and good input. Anything and everything goes into my hairtop computer and mulls around for awhile; The boys are a hit and miss right now as far as working on the boat. Try to get them involved in the stuff that dosn't require a mask and alot of protective clothing.
    Posted 06-05-2008 at 12:27 AM by Old Hickory Old Hickory is offline
    Updated 06-05-2008 at 03:05 AM by Old Hickory
  4. Old Comment
    teamhart2's Avatar
    Lookin good, when do we get to see it go in? Also, with the convincer style transom how are you gonna mount the motors? outboard bracket? or are they gonna mount normally on the new transom? havin a hard time picturin what your plannin in my head
    Posted 06-06-2008 at 02:15 PM by teamhart2 teamhart2 is offline
  5. Old Comment
    Old Hickory's Avatar
    going to try and get it bedded this weekend. I made a set of transom clamps on tuesday and hope to use them sunday. This grinding is wearing me out. As far as mounting my twin engines I'll be using a transom extension.

    I havn't made up my mind yet as to how I'm going to build and finish the rear of the deck. I have several options, but when finished it should look very similar to the south end of a convincor.
    Posted 06-19-2008 at 02:46 AM by Old Hickory Old Hickory is offline
  6. Old Comment
    Boston Predictor's Avatar
    Man It almost looks like you know what you're doing!

    Really though, hats off to you. Tough project to tackle, and you're doing great. :cheers

    I have been so busy these past months I haven't really had much time to check in and see how the project is coming along. Any late breaking developments??

    I've said it before - This truly is one of the coolest projects on the site! I love the enforcers and one w/ twins??!!!

    Unprecedented

    I've updated my subscription to this blog
    If there is anything I can do to help, shoot me a PM or give me a call 781 467 8475.

    Geoff
    Posted 11-05-2008 at 12:39 PM by Boston Predictor Boston Predictor is offline
  7. Old Comment
    Old Hickory's Avatar
    Thanks BP;

    I've got quite abit done. Transom is bedded and I have completely enclosed the rear deck and rebuilt the stearn. just need to use some filler to smooth it out and do final prep for the glass. Just havn't had time to post. Been busy w/ kids and sports. hopefully I'll post pics and progress soon.

    Hick
    Posted 11-06-2008 at 09:59 AM by Old Hickory Old Hickory is offline
 

All times are GMT -4. The time now is 10:17 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright 2002-2019 Checkmate-Boats.com & Whitecap Enterprises Corp. All Rights Reserved.
Images & Content are Copyright material and may not used without prior written permission.