-
Welcome to the Checkmate Community Forums forums.
» Interact with over 10,000 Checkmate Fanatics from around the world!
You are currently viewing our boards as a guest which gives you limited access to view most discussions, articles and access to our other FREE features.
By joining our free community you will be able to:
» Post topics and messages
» Post and view photos
» Communicate privately with other members
» Access our extensive gallery of old Checkmate brochures located in our Media Gallery
» Browse the various pictures in our Checkmate photo gallery
Registration is fast, simple and absolutely free so please, join our community today!
If you have any problems with the registration process or your account login, please contact support by clicking here or by using the"contact us" link at the bottom of the page.
Recent content by dusturbd
-
D
1986 Enchanter 21
fell free to make a legit offer but this is not a fire sale Thanks- dusturbd
- Post #2
- Forum: Checkmate Listings
-
D
1986 Enchanter 21
1986 Checkmate 21' Enchanter This is a very nice boat that is a truly turn key needs nothing boat. I have gone thru every system on this boat and either rebuilt, replace or checked and have many receipts. Hull The hull has been wet sanded, buffed, polished and waxed, the strips where...- dusturbd
- Thread
- Replies: 3
- Forum: Checkmate Listings
-
D
Why is motor offset
Problem fixed it wasn't the motor that was offset let's just say it was improper use of the measuring stick Doh- dusturbd
- Post #4
- Forum: Props, Setups & Rigging
-
D
Why is motor offset
And it steers very light to port and heavy to starboard- dusturbd
- Post #2
- Forum: Props, Setups & Rigging
-
D
Why is motor offset
I just noticed that my 86 enchanter has the motor offset to the port side 1" and these holes are original there is no signs that any holes have been filled and redrilled So my question is why and could this be the cause of the boat not going straight at idle/slow speed Thanks- dusturbd
- Thread
- Replies: 4
- Forum: Props, Setups & Rigging
-
D
1999 200efi merc
I'm kind of torn at the moment about selling it, I looked it up on nada and they show low retail for an average motor is $2995 I fell this one is far from average with all the work and upgrades it has done to it I am thinking complete with jack plate and SS prop it would take $4500 for me to...- dusturbd
- Post #5
- Forum: Engines and Components
-
D
1999 200efi merc
spoke with mercury today to verify info it is a 1999 2.5L 200efi L it is NOT an XL it has a 20" mid section also left out of above post is 10 new powerhead studs washers and nuts. don't guess I can post pics direct here but can email them or text them. Thanks- dusturbd
- Post #2
- Forum: Engines and Components
-
D
1999 200efi merc
I have a 1999merc 200efi that I believe is an xl it has been well maintained and runs great it has right at 125 psi on all 6 cylinders. The engine has a Bobs low water pickup, Bobs solid aluminum upper and lower mounts, new mercury SS swivel pin and yoke with all new swivel pin bushings and...- dusturbd
- Thread
- Replies: 5
- Forum: Engines and Components
-
D
Engine rigging pic wanted for 99 Merc 200 efi.
I have a 99 200efi on an enchanter and all the cables ect go in on the port side- dusturbd
- Post #5
- Forum: Props, Setups & Rigging
-
D
1991 maxxum 281
Ok first if it's done it since new why wasn't it fixed under warranty? But both of those problems could be leaky injectors if they are leaking badly they are flooding it when it's hot and cold is because there's no fuel in the rails after it all leaks out but could be issues with bypass valve...- dusturbd
- Post #2
- Forum: Engine Technical Discussion